Water rising in the pit with a silent pump comes first
Before you touch anything, look at the floor. If water has spread near an outlet, an extension cord or the furnace, stay out of it and switch off the breaker for the basement from a dry spot. If the floor is dry, you can safely check a few things. Is the pump plugged in, and has the ground-fault outlet it plugs into tripped? Press its reset button once. Is the breaker on? With the pump unplugged, look into the pit: a float that has caught on the side of the pit or on the power cord cannot rise, so the pump never gets told to start.
If the pump hums but moves no water, or the reset will not hold, leave it unplugged and call. A pump that hums without pumping can overheat. While you wait, easing up on laundry and long showers does no harm, and in a house on a septic system it is a good habit whenever anything in the basement is not working properly. If water is already coming across the floor, treat it as an emergency.
A pump that never stops, or starts every few seconds, has a fault worth finding
A pump that runs on and on with little water coming in often has a float switch stuck in the on position, or a check valve that has failed. When the check valve on the discharge pipe lets go, the water the pump just lifted falls back into the pit and the pump starts again. You may hear a thump or a gurgle each time it shuts off. Either way the motor wears out much faster than it should.
In deep cold the problem can be outside. Where the discharge line leaves the house, a section that holds water can freeze solid in a January night, and the pump then pushes against ice. A pump that runs hard, gets warm and moves no water in midwinter usually has this problem. Do not try to thaw the line with an open flame. Leave it with the plumber, who will clear the line and look at how it is laid out so it drains instead of holding water.
Other signs worth a call are rust or oily marks on the pump housing, a burning smell, gravel or silt in the pit, and a pit that stays dry all spring while the basement walls feel damp. That last one can mean the water is not reaching the pit at all.
Spring melt is when the pump works hardest
Environment Canada's 1981 to 2010 normals for Fergus Shand Dam, the weather station near Alma, record 147.8 cm of snow a year. When that snow melts, the ground around the foundation fills with water, and sump pumps and foundation drains carry their heaviest load. A pump that copes in a dry August can fall behind in a wet April, so test it before the thaw, while there is still time to deal with a weak one.
How much a sump does for you depends on the age of the house. The stone-basement houses on Peel Street West, Church Street and Simpson Street were built in the 1850s to 1890s with no perimeter drain, so the walls take on water and many of those basements have never had a sump. Adding a pit can help with standing water, but it will not make a stone basement fully dry. The plumber will tell you plainly what to expect before you decide.
Houses from the 1930s to the 1950s along Wellington Road 7 and Wellington Road 17 usually have a floor drain where a newer house would have a sump. When that floor drain is what takes the water in spring, a sump pit and pump can be a sensible change. New homes, including the subdivision planned off Wellington Road 17, are designed with weeping tile around the footings that drains to a sump pump. In those houses the pump is what keeps the weeping tile working, so it is not optional.
Battery backup on a rural power line
Spring storms and winter ice bring down rural lines, often on the same nights the ground is wettest. When the power goes out in a house on a well, the well pump stops, so the taps go dry, and the sump pump stops with it. A battery backup pump sits in the same pit, next to the main pump or just above it, and starts on its own when the water rises past the main pump's level. Many units also sound an alarm, so you know the main pump has stopped.
Some backup pumps run on water pressure instead of a battery. They rely on a steady supply from a town main, so they are not suited to a house where the water comes from a well pump that has also lost power. For Alma homes a battery unit is the practical choice. The plumber will size the battery to how fast your pit fills and explain how to check it each season. A battery that sits unused for years may not hold a charge when you need it, so test it now and then.
What a sump pump visit involves
The plumber will ask what you have seen and when it started, then fill the pit with water and watch a full cycle. That shows whether the float rises freely, whether the pump empties the pit at a reasonable rate and whether the check valve holds. They look at the discharge line from the pit to where it leaves the house, check the pump's outlet and cord, and note any silt or gravel that suggests the weeping tile is carrying soil.
After that you get a clear explanation: a part that can be replaced, such as the float switch or the check valve, or a pump that should be changed. You see a written price and approve it before any part is fitted. A new pit, or changes to the drains that go with it, may need a building permit. The municipal building department decides whether a given job does, and the plumber will tell you when to ask. Work is performed by licensed plumbers (306A Certificate of Qualification).
If damp in the basement turns out to come from a drain or the line to the septic tank rather than groundwater, see sewer repair or drain cleaning.
